Perkins 4.108 motordeler

A genuine Perkins 'spin -on' fuel filter assembly kit, to replace the original factory fitted 'cartridge type' filter housing or a Delphi 296 filte...

Aftermarket Perkins 4.108 high quality water separator (pre-filter) with re-usable internal gauze strainer and glass bowl. This universal sedimente...

Delphi fuel filter assembly Drain Plug and sealing washer. Thread diameter 7.5mm UK, European and worldwide shipping is available.

High quality aftermarket fuel banjo bolt set, includes: x4 Banjo bolts UK, European and Worldwide shipping available.

A pair of (pencil style) Perkins 4.108 Lowline heat exchanger Anodes. This Anode is located inside a blanking plug (see photo). Quality product ...

Perkins manufactured three marinized versions of Perkins 4.108 engines over the years, each with different options for the header tank used. See ph...

Standard single spade aftermarket oil pressure switch for Perkins 4.108 engines. Equivalent to Perkins 2848062 Tapered screw thread Single spade ...

A pair of high quality aftermarket end caps for the later versions of the Perkins 4108M marine engine fitted with 'Bowman' type heat exchanger. Th...

Quality aftermarket 4.108 'breather hose' kit replaces the right angle hose located between the rocker cover and the inlet cowl on all factory mari...

High quality Nautilus Fuel Master marine grade fuel hose. Specification: A1 grade, Lloyds approved and conforms to ISO 7840 2013 and SAE J1527 I...

Strong, good quality Stainless Steel (304 grade) worm drive clamps ideal for both the marine environment and industrial use. Band width 12.5mm ...

Quality aftermarket Perkins 4.108M Lowline and Bowman (Marine) coolant hose replacement kit. The Lowline kit contains eleven hoses with stainless ...

We can now offer an Repaired exhaust elbow connector for Perkins 4.108 marine engines. With time the original cast iron part will fail due to corro...

A set of replacement heat exchanger and oil cooler seals for Perkins 4.108 'lowline' engines. These are high quality nitrile rubber seals, manufact...

Perkins 4.108 Jabsco raw water pump drive. This part is only suitable for the Jabsco raw water pumps. UK, European and Worldwide shipping available.

A quality aftermarket aluminium thermostat housing to fit Perkins 4.108 marine engines. Kit includes: Thermostat housing Housing gasket Free 5...

High quality aftermarket Perkins 4.108 Jabsco raw water pump drive shaft coupling UK, European and Worldwide shipping available.

A set of 4 genuine Perkins exhaust manifold studs, to fit Perkins 4.108 engines. Total length = 50mm Stud protrudes 37mm measured form cylinder he...

A quality aftermarket bulkhead mounted warning alarm for Perkins 4.108, supplied with a high temperature switch. Ideal for marine use, as it gives...

Aftermarket Perkins 4.108 Temperature sender adapter; thread size 1/2" to 3/8"NPT UK, European and Worldwide shipping available

High quality aftermarket Perkins 4.108 coolant inlet connector. This is the short tube that is pressed into the block just below the alternator pos...

Aftermarket Perkins 4.108 drip rail; it returns fuel from the top of the injectors back to the filter housing. We now manufacture these, Perkins ha...

A set of aftermarket gaskets and seals to overhaul your CAV DPA fuel pump on your Perkins 4.108. We stock both options for either the mechanically...

Aftermarket Perkins 4.108 Injector pump Anti stall valve for use on injector pumps with an Hydraulic Governor. Includes: Anti stall valve UK, E...

High quality aftermarket Perkins 4.108 Water pump back plate fitted between the water pump and the engine block. Equivalent to Perkins Part No. 024...

Genuine Perkins 4.108 Injector pipes to fit engines with a mechanically governed injector pump. (See photos to view a mechanically governed pump) ...

An aftermarket Perkins Injector Flange - Equivalent to OE Part No. 36173452. Suitable for Perkins 4.99, 4.107 and 4.108 engines. Injector clamps ca...

Aftermarket Delphi blanking plug kit for Filter Assembly Includes: x2 Blanking plugs (1/2"UNF thread) x2 Blanking plug copper washers x1 Air vent ...

Aftermarket 12 to 24v Isolated earth oil pressure sender for Perkins 4.108 with 2 options available: Earth return sender - uses the outer casing...

Aftermarket Low oil pressure alarm for Perkins 4.108 is a quality bulkhead mounted warning alarm, to be used in conjunction with an oil pressure sw...

Quality aftermarket Perkins 4.108 Exhaust Outlet Gasket UK, European and Worldwide shipping available.

Genuine Perkins 4.108M replacement Exhaust outlet elbow. We offer two options with different positions for the water pipe connection, top or side....

Quality aftermarket Perkins 4.108M (Marine version to fit front mounted heat exchanger) coolant hose replacement kit, contains 5 hoses with stainl...

A Perkins 4.108 Exhaust Outlet elbow, this is a robust 'budget' aluminium aftermarket alternative, available in two versions, straight and 45 degre...

Genuine Bowman combined exhaust manifold and heat exchanger that fits Perkins 4.108 - Bowman Part No. 2486H005 This is a high quality original equi...

Quality aftermarket Perkins 4.108 Water pumps manufactured specifically for us and to our high quality requirements. They are available with either...

Genuine Jabsco bronze sea water pump as fitted to all Perkins 'UK factory marinized' versions of the Perkins 4.108 engine. The pump is engine drive...

Quality aftermarket 'standard impeller kits' and 'raw water pump service kits' for the factory marinized version of Perkins 4.108 fitted with the b...

Aftermarket Perkins 4.108 thermostat kit with the correct 82oC opening temperature for automotive and industrial applications. For marine applicati...

Quality aftermarket Perkins 4.108 raw water pump connecting kit enables you to attach or replace the standard Jabsco raw water pump fitted to these...

Quality aftermarket Perkins 4.108 exhaust elbow hose connector kit. Included are all the parts required to connect the Bowman heat exchanger end ca...

Perkins 4.108 aftermarket stainless steel exhaust outlet elbow - equivalent to 413165509. Manufactured from 316 Stainless steel. This is a superbly...

High quality aftermarket Perkins 4.108 raw water pump mounting gaskets, to fit a 'Jabsco' raw water Pump Kit contains: x1 Pump to mounting plate...

A genuine Bowman Filler neck assembly for a Bowman type heat exchanger as fitted on later versions of the Perkins 4.108 engine. Bowman Part No. 392...

A Mono Ethylene Glycol (MEG) based engine coolant and anti-freeze concentrate from Comma. Gives up to 2 years protection against freezing and overh...

Standard aftermarket ethylene glycol concentrate (antifreeze) from MPM, can be used throughout the whole year in the cooling systems of petrol and ...

A set of five quality aftermarket raw water pump cover plate gaskets. Outside diameter 76mm Equivalent to Pekins part number 0490785 Equi...

Lloyds Approved Nautilus Marine Exhaust Hose. This is a strong but flexible rubber hose manufactured from synthetic textile fabrics and reinforced ...