Perkins 4.107 / 4.108 / 4.99 motordeler

Reconditioned Perkins 4.108 injector. These injectors are disassembled, all the parts are checked, new nozzles fitted, calibrated and tested. We al...

Genuine Perkins 4.107 and 4.108 push rods to fit all engine versions, Options: New genuine Perkins push rod Used (genuine Perkins ) push rod s...

Genuine Perkins 4.108 Injector pipes to fit engines with a mechanically governed injector pump. (See photos to view a mechanically governed pump) ...

A quality aftermarket set of main bearings fit to all versions of the Perkins 4.108 engine. Available in the following sizes: Standard -0.010" -0....

Quality aftermarket 12 volt 65+ amp, 'high output' alternators fit all versions (including marine) of Perkins 4.108 engines set up for a 'three lug...

High quality aftermarket Perkins 4.107 Water pumps manufactured specifically for us. They are available with either the standard pulley for a 12 mm...

Aftermarket fuel washers and seal kit for Perkins 4.107 Series engines. Kit Includes: x4 Injector copper washers x8 Fuel return pipe washe...

Aftermarket Perkins 4.108 tab washer kit, includes: x1 Flywheel locking tab washer - prevents the flywheel to crank bolts from working loose. x...

Genuine Perkins 4.108 injector flange / clamp. Can be simply replaced if broken by removing the injector nozzle. UK, European and Worldwide shippin...

Perkins 4.108 Raw water pump alignment tool, used to center the adaptor plate to ensure reduced wear on the drive shaft components as specified in ...

A quality aftermarket glowplug for Perkins 4.108 engines. Fits late type cylinder heads, where the glowplug is directly screwed into the cylinder ...

A genuine Bowman Filler neck assembly for a Bowman type heat exchanger as fitted on later versions of the Perkins 4.108 engine. Thread size 1 1/4 ...

Perkins 4.107 Front crankshaft /timing cover oil seal, a quality aftermarket lip seal. UK, European and Worldwide delivery available.

Good quality aftermarket water temperature sender that fits the majority of early Perkins 4.107 engines. Details: Spade type electrical connection...

A Mono Ethylene Glycol (MEG) based engine coolant and anti-freeze concentrate from Comma. Gives up to 2 years protection against freezing and overh...

Perkins 4.108 pre-combustion chamber insert These are quality genuine Perkins OE parts and are suitable for all Perkins 4.108 engines.We also now i...

High quality aftermarket engine mounts for Perkins 4.107M marine engines. Fitting the correct type of mount for the weight and use of your engine i...

JB MarineWeld is a specially formulated two part Cold-Weld adhesive system that provides strong, lasting repairs for bonding different or similar s...

If you have one of the early marine versions of these engines with the paper oil filters inside a re-useable steel housing, then you will know what...

A high quality aftermarket kit of standard size piston rings for your Perkins 4108. These ring sets fit all 5 ring pistons on this engine and also ...

High quality aftermarket Perkins 4.108 Oil filler caps available in two sizes: 62mm (external diameter) for marinised engine versions 45mm (extern...

Quality aftermarket 14 Volt 70 Amp Insulated return alternator 'three lug' mounted alternator. The adjuster arm securing bolt is at a 120 degree an...

High performance electrical relay with mounting bracket suitable for high current switching. Details: 12v 100 amp Dimensions 4.5cm x 4.5cm x 7cm C...

A set of gaskets and seals to overhaul your CAV DPA fuel pump on your Perkins 4.107. We stock both options for either the mechanically or hydraulic...

This quality set of main bearings fit all versions of Perkins 4.107 engine. They can be supplied as standard, 0.010" 0.020" or 0.030" undersize. Yo...

Aftermarket Rear crankshaft upgrade kit, the 'Achilles heel' of Perkins 4.107 design is the crankshaft rear rope seal which is notorious for leakin...

Genuine Bowman 3366 oil cooler end cover for Perkins 4.108Dimensions are: Internal hole size 52 mm and 28 mm length 55 mm UK, European and Worldw...

Quality aftermarket Perkins 4.108 raw water pump connecting kit enables you to attach or replace the standard Jabsco raw water pump fitted to these...

A genuine Perkins 4.108 oil pressure relief valve kit. It includes the following items: Plunger Spring Spring cap Cotter pin UK, European ...

High quality aftermarket 12 volt 90 amp high output alternators fit all versions Perkins 4.108 (including marine) of these engines set up for a 'th...

Aftermarket 12 to 24v Isolated earth oil pressure sender for Perkins 4.107 with 2 options available: Earth return sender - uses the outer casing t...

High quality aftermarket This 12 volt Perkins alternator fits the Perkins 4.108 'lowline' marine engine. The adjuster arm securing bolt is at a 180...

A very comprehensive set of quality aftermarket gaskets and seals for the bottom end of your Perkins 4.107, including marine versions. water pump ...

High quality aftermarket Perkins 4.107 Timing cover gasket and front crankshaft oil seal set. Details: x1 Timing cover gasket manufactured from an...

Aftermarket alternator wiring connector kit, commonly known as a 'euro connector'. Fits many standard 3 pin alternators. UK, European and Worldwide...

Aftermarket Perkins 4.108 Injector pump Anti stall valve for use on injector pumps with an Hydraulic Governor. Includes: Anti stall valve fixi...

A comprehensive aftermarket kit which includes the major components that you will need to overhaul your tired cylinder head on your Perkins 4.107. ...

A quality set of aftermarket connecting rod bearings (big ends) to fit all Perkins 4.107 engines. The following sizes are available: Standard -0.0...

Genuine Jabsco bronze sea water pump as fitted to all Perkins 'UK factory marinised' versions of the Perkins 4.107 engine. The pump is engine drive...

Genuine Perkins exhaust manifold studs in a set of 4 to fit Perkins 4.107 engines Total length = 50mm Stud protrudes 37mm form cylinder head face ...

High quality aftermarket Perkins 4.107 coolant inlet connector. This is the short tube that is pressed into the block just below the alternator pos...

High quality aftermarket 12 volt 65+ amp alternators fit all versions (including marine) of Perkins 4.107 engines set up for a 'three lug' mounted ...

Quality aftermarket Perkins 4.107 12v cold start plug (thermostart) available with either: 'push on' 'spade' connection, or 'screw' type connec...

Lloyds Approved Nautilus Marine Exhaust Hose. This is a strong but flexible rubber hose manufactured from synthetic textile fabrics and reinforced...

Quality aftermarket single spade oil pressure switch fits Perkins 4.107 that take an earth supply from the engine block. It has a tapered screw th...

We are pleased to offer a Perkins 4.108 DPA injector pump repair service . The pumps are disassembled, completely cleaned, inspected and worn parts...

Quality aftermarket Perkins 4.107 starter solenoids suitable for automotive' or a marine applications. Our automotive version is suitable for appl...

Genuine Bowman Standard oil cooler designed for use on marine transmissions for Perkins 4.108. Features cupro-nickel tubes for long life expectancy...