Perkins 4.108M Engine Parts

Reconditioned (low hours) Perkins 4108 basic engine block with crank and pistons. Originally used by the MOD as generator engines, which we fully s...

A comprehensive aftermarket kit which includes the major components that you will need to overhaul your tired and smoking Perkins 4108 engine This ...

Genuine Perkins 4.108 Cylinder head studs - Part No. 32524138  Details: Length 105mm Ø 11mm Please note these studs are not suitable for 4.99 or 4...

Genuine Perkins 4.108 Cylinder head nut set (used). Theses parts new from Perkins retail at more then £250.00 GBP! Set includes: x12 Standard ...

Genuine Perkins 4.108 drive gears, USED but in excellent condition. These were removed from a Ex-MOD auxiliary generator (very low hour use )The op...

Genuine Perkins 4.107 and 4.108 push rods to fit all engine versions - Part No. 31434306 Options:  New genuine Perkins push rod Used (genuine Perk...

A set of 4 genuine Perkins exhaust manifold studs, to fit Perkins 4.108 engines. Total length = 50mm Stud protrudes 37mm measured form cylinder he...

Genuine used Perkins 4.108 timing cover 'oil slinger' (Used) UK, European and Worldwide shipping available.

A set of aftermarket gaskets and seals to overhaul your CAV DPA fuel pump on your Perkins 4.108. We stock both options for either the mechanically...

Perkins 4.108 DPA injector pump Cover Plate Part number 7180-57A To fit hydraulicly governed pumps Please check this is correct for your pump as t...

Replacement Perkins fuel filter assembly for Perkins 4.108 engines. This genuine Delphi quality part has the correct 1/2" UNF thread original fitti...

Genuine Perkins 4.108 Injector pipes to fit the lowline marine engine version, with the following build codes: ED13630, ED13631, ED22111, ED22714,...

Perkins manufactured three marinized versions of Perkins 4.108 engines over the years, each with different options for the header tank used. See ph...

A set of replacement heat exchanger and oil cooler seals for Perkins 4.108 'lowline' engines. These are high quality nitrile rubber seals, manufact...

Replacement 12 Volt, 16 ohm stop solenoid that fits the later versions of Perkins 4.108 fitted with electrically operated stop solenoid that screws...

Quality aftermarket Perkins 4.108M Lowline and Bowman (Marine) coolant hose replacement kit. The Lowline kit contains eleven hoses with stainless ...

We can now offer an Repaired exhaust elbow connector for Perkins 4.108 marine engines. With time the original cast iron part will fail due to corro...

Genuine Perkins 4.108M replacement Exhaust outlet elbow.  We offer two options with different positions for the water pipe connection, top or side....

High quality aftermarket Perkins 4.108 Jabsco raw water pump drive shaft coupling UK, European and Worldwide shipping available.

A set of replacement heat exchanger and oil cooler seals for Perkins 4.108M early and later 'lowline' version. These are high quality nitrile rubbe...

Quality aftermarket Perkins 4.108 raw water pump connecting kit enables you to attach or replace the standard Jabsco raw water pump fitted to these...

A quality aftermarket aluminium thermostat housing to fit Perkins 4.108 marine engines. Kit includes: Thermostat housing Housing gasket Free 5...

A quality aftermarket bulkhead mounted warning alarm for Perkins 4.108, supplied with a high temperature switch. Ideal for marine use, as it gives...

JB Marine Weld is a specially formulated two-part steel reinforced epoxy cold weld system that provides for strong, lasting repairs for bonding dif...