Perkins Engine Parts

Perkins 402C-05 aftermarket head gasket details: Depth 1.3mm UK, European and Worldwide shipping available.

A set of quality aftermarket Perkins 400 series 402D-05 connecting rod bearings for engine build code beginning GG Standard size only UK, Europea...

A quality set of aftermarket thrust washers for Perkins 4.99 engines. Please note that they are standard size. The set is manufactured for us to s...

High quality aftermarket Perkins 4.99 coolant inlet connector. This is the short tube that is pressed into the block just below the alternator posi...

Aftermarket Perkins 4.99 sump bolt. This part will fit all sumps drilled to take a parallel thread (the majority) sump drain bolt. Diameter across ...

Quality aftermarket Perkins 4.248 Rear crankshaft oil seal. Equivalent to Perkins Part No. 2418F475 UK, European and Worldwide shipping available.

We have recently sourced a limited number of genuine (old stock) Perkins 4.99 & 4.107 mechanically governed injector pumps. These pumps have be...

We can now offer an Repaired exhaust elbow connector for Perkins 4.107 marine engines. With time the original cast iron part will fail due to corro...

Quality aftermarket Perkins 4.99 Front crankshaft oil seal. Equivalent to Perkins Part No. 0730098 UK, European and Worldwide shipping available.

High quality aftermarket 12V earth return starter motors for Perkins 4.248. Fit all versions (including marine) of these engines set up for a 'thre...

Coolant drain tap for this Perkins 4.99 engine. This is a quality aftermarket part and is fully machined from solid brass. Equivalent to Perkins 31...

We are pleased to offer a Perkins 4.99 DPA injector pump repair service . The pumps are disassembled, completely cleaned, inspected and worn parts ...

Quality aftermarket 12 to 24v oil pressure sender for Perkins 4.99 with 2 options available: Earth return sender - uses the outer casing to prov...

High quality aftermarket Perkins 4.99 raw water pump connecting kit enables you to attach or replace the standard Jabsco raw water pump fitted to t...

A comprehensive aftermarket overhaul kit which includes the major components that you will need to overhaul your tired Perkins 4.248 cylinder head....

Aftermarket starter/ignition switch for Perkins 4.238 engines, including marine versions. We offer two switch options, which have either 4 pin or 6...

Aftermarket Injector leak-off rail that fits all versions of the Perkins 4.248. It has threaded outlets at both ends and is quality anodized produc...

Quality aftermarket replacement 12 Volt, 16 ohm stop solenoid that fits the later versions of Perkins 4.248 fitted with electrically operated stop ...

Aftermarket Perkins 4.248 series Thermostat - equivalent to Perkins Part No. 2485613 Fits engines with codes beginning: LF - 4.248 LG - 4.2482 82°...

Reconditioned Perkins 4.107 injector. These injectors are disassembled, all the parts are checked, new nozzles fitted, calibrated and tested. We al...

Perkins 4.99 Raw water pump alignment tool, used to centralise the adaptor plate to ensure reduced wear on the drive shaft components and as specif...

A quality aftermarket set of main bearings, fits all versions of the Perkins 4.248 engine. Size options are: standard -0.010" -0.020" -0.030" To ...

Quality aftermarket Perkins 4.236 & M90 Crankshaft Thrust block, for Crankshafts with a 3 bolt 'pully end' External diameter 56mm Comes wit...

Genuine OE Perkins alternator belts which are the correct fitment for Perkins 4.248 engines. *Please note that there are different belt lengths on ...