Perkins 4.108 Engine Parts

Quality aftermarket Perkins 4.108 exhaust elbow hose connector kit. Included are all the parts required to connect the Bowman heat exchanger end ca...

Quality aftermarket Perkins 4.108M Lowline and Bowman (Marine) coolant hose replacement kit. The Lowline kit contains eleven hoses with stainless s...

A set of four excellent injector nozzles for Perkins 4.108 engines that have the correct type of tip for all marine and automotive versions of this...

Aftermarket starter/ignition switch for Perkins 4.108 engines, including marine versions. We offer two switch options, which have either 4 pin or 6...

Rydlyme Marine is a safe, biodegradable marine descaler developed to dissolve problematic fouling mediums including calcium, rust, mussels, barnacl...

Quality aftermarket Perkins 4.108 Exhaust Outlet Gasket UK, European and Worldwide shipping available.

A genuine Perkins OE fuel filter for servicing your Perkins 4.108 engine. This filter was fitted to the earlier versions of the 4.108 engine. UK, ...

High quality aftermarket Perkins 4.108 coolant inlet connector. This is the short tube that is pressed into the block just below the alternator pos...

Replacement 12 Volt, 16 ohm stop solenoid that fits the later versions of Perkins 4.108 fitted with electrically operated stop solenoid that screws...

Quality aftermarket 4.108 'breather hose' kit replaces the right angle hose located between the rocker cover and the inlet cowl on all factory mari...

A pair of Stainless Steel T-bolt clamps with a fixed bridge, ideal for securing an exhaust hose to the heat exchange outlet on marine engines. Prod...

Strong, good quality Stainless Steel (304 grade) worm drive clamps ideal for both the marine environment and industrial use. Band width 12.5mm Opt...

Coolant drain tap for this Perkins 4.108 engine. This is a quality aftermarket part and is fully machined from solid brass. These drain taps have t...

A quality aftermarket bulkhead mounted warning alarm for Perkins 4.108, supplied with a high temperature switch. Ideal for marine use, as it gives ...

We can now offer an upgraded exhaust elbow connector for Perkins 4.108 marine engines. With time the original cast iron part will fail due to corro...

Delphi fuel filter assembly Drain Plug and sealing washer. Thread diameter 7.5mm UK, European and worldwide shipping is available.

Genuine Perkins 4.108 Injector pipes to fit engines with a mechanically governed injector pump. (See photos to view a mechanically governed pump) ...

High quality aftermarket Perkins 4.108 raw water pump mounting gaskets, to fit a 'Jabsco' raw water Pump Kit contains: x1 Pump to mounting plate g...

We are now pleased to offer a Perkins 4.108 Exhaust outlet elbow kit, manufactured from 316 Stainless steel. This is a superbly engineered aftermar...

Perkins 4.108 front crankshaft / timing cover oil seal, a quality aftermarket lip seal. UK, European and Worldwide shipping available.

Aftermarket Perkins 4.108 high quality water separator (pre-filter) with re-usable internal gauze strainer and glass bowl. This universal sedimente...

Aftermarket Low oil pressure alarm for Perkins 4.108 is a quality bulkhead mounted warning alarm, to be used in conjunction with an oil pressure sw...

A quality aftermarket aluminium thermostat housing to fit Perkins 4.108 marine engines. Kit includes: Thermostat housing Housing gasket Free 5ml H...

JB Marine Weld is a specially formulated two-part steel reinforced epoxy cold weld system that provides for strong, lasting repairs for bonding dif...

Aftermarket Delphi blanking plug kit for Filter Assembly includes: x2 Blanking plugs (1/2"UNF thread) x2 Blanking plug copper washers x1 Air v...

A robust oil filter wrench from Draper, ideal to remove your Perkins 4.108 screw-on oil filter Specification: Maximum oil filer diameter 100 mm Pl...

A genuine Perkins 4.108 oil filter for servicing your Perkins 4.108 and (4.108M marine) engine. There are two types of filters used on these engin...

A quality set of aftermarket Perkins 4.108 connecting rod bearings available in the following sizes: Standard -0.010" -0.020" -0.030" To help you...

Universal 12V to 24V waterproof Temperature gauge with sender. This high quality product has been manufactured solely for Parts4engines and is desi...

Perkins 4.108 pre-combustion chamber insert These are quality genuine Perkins OE parts and are suitable for all Perkins 4.108 engines.We also now i...

A set of five quality aftermarket raw water pump cover plate gaskets. Outside diameter 76mm Equivalent to Pekins part number 0490785 Equiv...

Genuine Jabsco bronze sea water pump as fitted to all Perkins 'UK factory marinised' versions of the Perkins 4.108 engine. The pump is engine drive...

Quality aftermarket 12 volt 65+ amp, 'high output' alternators fit all versions (including marine) of Perkins 4.108 engines set up for a 'three lug...

A Perkins 4.108 Exhaust Outlet elbow, this is a robust 'budget' aftermarket alternative, available in two versions, straight and 45 degree. Details...

Genuine Perkins 4.108 injector flange / clamp. Can be simply replaced if broken by removing the injector nozzle. UK, European and Worldwide shippin...

Perkins 4.108 Raw water pump alignment tool, used to center the adaptor plate to ensure reduced wear on the drive shaft components as specified in ...

Quality aftermarket Perkins 4.108 Raw Water Pump Hose Tails (pair) to fit hose diameter 26 mm. UK, European and Worldwide delivery available.

A Lucas heavy duty relay with detachable mounting bracket. These high quality waterproof relays were extensively used on Perkins marine wiring loom...

A quality aftermarket heavy duty zinc shaft anode. Manufactured to US military specification by Tecnoseal in Italy, one of the worlds leading suppl...

A genuine Bowman Filler neck assembly for a Bowman type heat exchanger as fitted on later versions of the Perkins 4.108 engine. Thread size 1 1/4 ...

Genuine Bowman combined exhaust manifold and heat exchanger that fits Perkins 4.108. This is a high quality original equipment part as supplied by ...

Aftermarket Perkins 4.108 tab washer kit, includes: x1 Flywheel locking tab washer - prevents the flywheel to crank bolts from working loose. x...

Genuine Bowman 3366 oil cooler end cover for Perkins 4.108Dimensions are: Internal hole size 52 mm and 28 mm length 55 mm UK, European and Worldw...

High quality aftermarket Perkins 4.108 Jabsco raw water pump drive shaft coupling UK, European and Worldwide shipping available.

High quality aftermarket Perkins 4.108 Oil filler caps available in two sizes: 62mm (external diameter) for marinised engine versions 45mm (extern...

Quality aftermarket 14 Volt 70 Amp Insulated return alternator 'three lug' mounted alternator. The adjuster arm securing bolt is at a 120 degree an...

High performance electrical relay with mounting bracket suitable for high current switching. Details: 12v 100 amp Dimensions 4.5cm x 4.5cm x 7cm C...

Standard ethylene glycol concentrate (antifreeze) from MPM, can be used throughout the whole year in the cooling systems of petrol and diesel engin...