Perkins 4.107 / 4.108 / 4.99 Engine Parts

Coolant drain tap for this Perkins 4.108 engine. This is a quality aftermarket part and is fully machined from solid brass. These drain taps have ...

A comprehensive aftermarket kit which includes the major components that you will need to overhaul your tired cylinder head on your Perkins 4.107. ...

A quality set of aftermarket Perkins 4.108 connecting rod bearings available in the following sizes: Standard -0.010" -0.020" -0.030" To h...

Aftermarket fuel washers and seal kit for Perkins 4.107 Series engines. Kit Includes: x4 Injector copper washers x8 Fuel return pipe washers ...

A Perkins 4.108 Exhaust Outlet elbow, this is a robust 'budget' aftermarket alternative, available in two versions, straight and 45 degree. Details...

Replacement 12 Volt, 16 ohm stop solenoid that fits the later versions of Perkins 4.108 fitted with electrically operated stop solenoid that screws...

A quality aftermarket glowplug for Perkins 4.108 engines. Fits late type cylinder heads, where the glowplug is directly screwed into the cylinde...

Quality aftermarket 4.108 'breather hose' kit replaces the right angle hose located between the rocker cover and the inlet cowl on all factory mari...

Genuine Perkins 4.108 Injector pipes to fit engines with a mechanically governed injector pump. (See photos to view a mechanically governed pump) ...

A genuine Perkins OE fuel filter for servicing your Perkins 4.107 engine. This filter was fitted to the earlier versions of the 4.107 engine. If yo...

A set of gaskets and seals to overhaul your CAV DPA fuel pump on your Perkins 4.107. We stock both options for either the mechanically or hydrauli...

Perkins 4.108 Raw water pump alignment tool, used to center the adaptor plate to ensure reduced wear on the drive shaft components as specified in ...

A quality aftermarket aluminium thermostat housing to fit Perkins 4.108 marine engines. Kit includes: Thermostat housing Housing gasket Free 5...

High quality aftermarket engine mounts for Perkins 4.107M marine engines. Fitting the correct type of mount for the weight and use of your engine i...

Quality aftermarket Perkins 4.108 Raw Water Pump Hose Tails (pair) to fit hose diameter 26 mm. UK, European and Worldwide delivery available.

Good quality aftermarket water temperature sender that fits the majority of early Perkins 4.107 engines. Details: Spade type electrical connecti...

Quality Perkins 4.108 Oil filter conversion kit. If you have one of the early marine versions of these engines with the paper oil filters inside a ...

Genuine Bowman combined exhaust manifold and heat exchanger that fits Perkins 4.108. This is a high quality original equipment part as supplied by ...

Reconditioned Perkins 4.108 injector. These injectors are disassembled, all the parts are checked, new nozzles fitted, calibrated and tested. We al...

Liqui Molly Marine Grease, is a long-lasting heavy-duty grease that reduces friction and wear. It has excellent aging and shear stability. Liqui M...

Quality aftermarket 12 volt 65+ amp, 'high output' alternators fit all versions (including marine) of Perkins 4.108 engines set up for a 'three lug...

A Mono Ethylene Glycol (MEG) based engine coolant and anti-freeze concentrate from Comma. Gives up to 2 years protection against freezing and overh...

Aftermarket Perkins 4.108 tab washer kit, includes: x1 Flywheel locking tab washer - prevents the flywheel to crank bolts from working loose. x...

High quality aftermarket Perkins 4.107 coolant inlet connector. This is the short tube that is pressed into the block just below the alternator pos...

JB MarineWeld is a specially formulated two part Cold-Weld adhesive system that provides strong, lasting repairs for bonding different or similar s...

Aftermarket Perkins 4.108 Injector pump Anti stall valve for use on injector pumps with an Hydraulic Governor. Includes: Anti stall valve ...

A quality aftermarket set of main bearings fit to all versions of the Perkins 4.108 engine. Available in the following sizes: Standard -0.010" ...

This quality set of main bearings fit all versions of Perkins 4.107 engine. They can be supplied as standard, 0.010" 0.020" or 0.030" undersize. Y...

Aftermarket Rear crankshaft Repair kit, the 'Achilles heel' of Perkins 4.107 design is the crankshaft rear rope seal which is notorious for leaking...

Genuine Perkins 4.108 injector flange / clamp. Can be simply replaced if broken by removing the injector nozzle. UK, European and Worldwide shippi...

Perkins 4.108 pre-combustion chamber insert These are quality genuine Perkins OE parts and are suitable for all Perkins 4.108 engines.We also now i...

A genuine Perkins 4.108 oil pressure relief valve kit. It includes the following items: Plunger Spring Spring cap Cotter pin UK, European ...

A very comprehensive set of quality aftermarket gaskets and seals for the bottom end of your Perkins 4.107, including marine versions. water pum...

Quality aftermarket Perkins 4.107 12v cold start plug (thermostart) available with either: 'push on' 'spade' connection, or 'screw' type connec...

A genuine Bowman Filler neck assembly for a Bowman type heat exchanger as fitted on later versions of the Perkins 4.108 engine. Thread size 1 1/...

Perkins 4.107 Front crankshaft /timing cover oil seal, a quality aftermarket lip seal. UK, European and Worldwide delivery available.

A quality set of aftermarket connecting rod bearings (big ends) to fit all Perkins 4.107 engines. The following sizes are available: Standard -...

Aftermarket 12 to 24v Isolated earth oil pressure sender for Perkins 4.107 with 2 options available: Earth return sender - uses the outer casing...

High quality aftermarket Perkins 4.108 Oil filler caps available in two sizes: 62mm (external diameter) for marinised engine versions 45mm (ext...

Lloyds Approved Nautilus Marine Exhaust Hose. This is a strong but flexible rubber hose manufactured from synthetic textile fabrics and reinforced ...

High performance electrical relay with mounting bracket suitable for high current switching. Details: 12v 100 amp Dimensions 4.5cm x 4.5cm x 7...

Quality aftermarket Perkins 4.107 starter solenoids suitable for automotive' or a marine applications. Our automotive version is suitable for ap...

Genuine Bowman 3366 oil cooler end cover for Perkins 4.108Dimensions are: Internal hole size 52 mm and 28 mm length 55 mm UK, European and W...

Genuine Perkins exhaust manifold studs in a set of 4 to fit Perkins 4.107 engines Total length = 50mm Stud protrudes 37mm form cylinder head fa...

Perkins 4.107 pre-combustion chamber insert These are quality genuine Perkins OE parts and are suitable for all Perkins 4.107 engines.We also now i...

High quality aftermarket 12 volt 65+ amp alternators fit all versions (including marine) of Perkins 4.107 engines set up for a 'three lug' mounted ...

Liqui Molly Anti-bacterial Diesel additive is a highly effective biocide designed to protect against bacteria, yeast and mold. Ideally suited for p...

High quality aftermarket Perkins 4.107 Timing cover gasket and front crankshaft oil seal set. Details: x1 Timing cover gasket manufactured from ...