Produkter

A genuine Perkins 4.108 oil pressure relief valve kit. It includes the following items: Plunger Spring Spring cap Cotter pin UK, European ...

Standard single spade aftermarket oil pressure switch for Perkins 4.108 engines. Tapered screw thread Single spade type electrical connection ...

A high quality aftermarket kit of standard size piston rings for your Perkins 4108. These ring sets fit all 5 ring pistons on this engine and also ...

Perkins 4.108 pre-combustion chamber insert These are quality genuine Perkins OE parts and are suitable for all Perkins 4.108 engines.We also now i...

Genuine Jabsco bronze sea water pump as fitted to all Perkins 'UK factory marinised' versions of the Perkins 4.108 engine. The pump is engine drive...

Perkins 4.108 Raw water pump alignment tool, used to center the adaptor plate to ensure reduced wear on the drive shaft components as specified in ...

Quality aftermarket Perkins 4.108 raw water pump end cover kit. The end covers on these pumps tend to wear, resulting in poor sealing of the impell...

Quality aftermarket Perkins 4.108 Raw Water Pump Hose Tails (pair) to fit hose diameter 26 mm. UK, European and Worldwide delivery available.

High quality aftermarket Perkins 4.108 raw water pump mounting gaskets, to fit a 'Jabsco' raw water Pump Kit contains: x1 Pump to mounting plate g...

Quality aftermarket 'standard impeller kits' and 'raw water pump service kits' for the factory marinised version of Perkins 4.108 fitted with the b...

Reconditioned (low hours) Perkins 4108 basic engine block with crank and pistons. Originally used by the MOD as generator engines, which we fully s...

Reconditioned Perkins 4.108 injector. These injectors are disassembled, all the parts are checked, new nozzles fitted, calibrated and tested. We al...

A set of eight genuine Perkins 4.108 rocker arm bushes. UK, European and Worldwide delivery available.

Quality aftermarket rocker cover gasket and seals set for Perkins 4.108. This set will stop your cover leaking oil and fits all versions of this en...

We are now pleased to offer a Perkins 4.108 Exhaust outlet elbow kit, manufactured from 316 Stainless steel. This is a superbly engineered aftermar...

Quality aftermarket starter solenoids from Prestolite suitable for Perkins 4.108 inertia type starter motors fitted to automotive' or a marine engi...

Replacement 12 Volt, 16 ohm stop solenoid that fits the later versions of Perkins 4.108 fitted with electrically operated stop solenoid that screws...

Perkins 4.108 sump bolt. This aftermarket part will fit all sumps drilled to take a parallel thread (the majority) sump drain bolt. Diameter across...

Aftermarket Perkins 4.108 Temperature sender adapter; thread size 1/2" to 3/8"NPT UK, European and Worldwide shipping available

A quality aftermarket aluminium thermostat housing to fit Perkins 4.108 marine engines. Kit includes: Thermostat housing Housing gasket Free 5ml H...

Aftermarket Perkins 4.108 thermostat kit with the correct 82oC opening temperature for automotive and industrial applications. For marine applicati...

This quality set of aftermarket thrust washers fits Perkins 4.108 engines. Please note that they are standard size. The set is manufactured for us ...

Genuine used Perkins 4.108 timing cover 'oil slinger' (Used) UK, European and Worldwide shipping available.

High quality aftermarket Perkins 4.108M and 4.108 Timing cover gasket and front crankshaft oil seal set. Details: x1 Timing cover gasket manufa...

Genuine Perkins 4.108 drive gears, USED but in excellent condition. These were removed from a Ex-MOD auxiliary generator (very low hour use )The o...

A very comprehensive set of quality aftermarket gaskets and seals for the top end of your Perkins 4.108 and 4.108M. Set includes: Cylinder head ga...

A comprehensive aftermarket kit which includes the major components that you will need to overhaul your tired cylinder head on your Perkins 4.108....

High quality aftermarket Perkins 4.108 coolant inlet connector. This is the short tube that is pressed into the block just below the alternator pos...

High quality aftermarket Perkins 4.108 Water pump back plate fitted between the water pump and the engine block. Two options are available: Mild s...

Quality aftermarket Perkins 4.108 Water pumps manufactured specifically for us and to our high quality requirements. They are available with either...

Good quality aftermarket water temperature sender that fits the majority of early Perkins 4.107 engines. Details: Spade type electrical connection...

Quality aftermarket 12 Volt, 150 Amp starter solenoid. This solenoid is for use with an Inertia type of starter motor. It requires a direct earth c...

High quality aftermarket engine mounts for Perkins 4.108M marine engines. Fitting the correct type of mount for the weight and use of your engine i...

Genuine Perkins 4.108M replacement Exhaust outlet elbow. We offer two options with different positions for the water pipe connection, top or side. ...

A set of replacement heat exchanger and oil cooler seals for Perkins 4.108M early and later 'lowline' version. These are high quality nitrile rubbe...

A pair of high quality aftermarket end caps for the later versions of the Perkins 4108M marine engine fitted with 'Bowman' type heat exchanger. The...

A set of quality aftermarket Perkins 4.154 (200 series) Cylinder head valves, set includes: x4 Inlet valves x4 Exhaust valves Fits all GA build co...

A compehensive aftermarket kit which includes the major components that you will need to overhaul your tired and smoking Perkins 4.154 (200 series)...

A quality aftermarket Perkins 4.154 (200 series) rocker cover gasket and seals set. Fits all (200 series) engines with build codes beginning wit...

A high quality standard aftermarket piston ring kit for Perkins 4.154 (200 series) engines. To fit the 3 ring piston used on the Japanese 200 vers...

Quality aftermarket Perkins 4.154 (200 series) alternator 12V fits all versions (including marine) of these engines set up for a 'three lug' mounte...

Low oil pressure alarm for Perkins 200 series is a simple bulkhead mounted warning alarm, to be used in conjunction with an oil pressure switch. Id...

An aftermarket Perkins 4.154 200 series raw water pump end cover kit. The end covers on these pumps tend to wear, resulting in poor sealing of the ...

Quality aftermarket 12 Volt 65+ Amp, 'high output' alternators fit all versions (including marine) of Perkins 4.154 engines set up for a 'three lug...

Quality aftermarket 12v Perkins 4.154 alternator, fits all versions (including marine) of these engines set up for a 'three lug' mounted alternator...

High quality alternator belt which are the correct fitment for standard engines Perkins 4.154. These standard belts are produced by 'Gates', the le...

A very comprehensive set of quality aftermarket gaskets and seals for the bottom end of your Perkins 4.154The set includes Timing cover inner an...

High quality aftermarket connecting rod (big-end) bearings with sintered aluminium bearing faces. They fit all versions of the Perkins 4.154 engine...